Skip to content
GETFASHION
Boots

Ankle Boots With Wide-Leg Pants: How to Get the Hem Length Right

Learn how to pin and measure wide-leg pants for ankle boots, choose full or cropped length, and adjust the hem for heeled or flat boots.

Ankle Boots With Wide-Leg Pants: How to Get the Hem Length Right

A pair of wide-leg pants can look sharp with ankle boots or sloppy, and a fraction of an inch of fabric often decides which. Hem them too long and the back of the leg drags under the heel until it frays. Hem them too short and the leg ends at an awkward point where a slice of boot shaft, or sock, shows at the wrong height.

The fix is to choose one of two lengths before anyone picks up scissors: a full length that covers most of the boot and nearly grazes the floor, or a cropped length that shows the boot while meeting the top of its shaft. Then pin it while you're wearing the exact boots you plan to pair with the pants.

Gather the boots and tools before you pin

Bring the boots you'll actually wear. Heel height and sole thickness set the hem, so pinning in sneakers or bare feet gives a length that's wrong as soon as you change shoes. If you own several pairs of women's ankle boots with different heels, pick the pair you'll wear most often with these pants.

You'll also need a few simple things to get an accurate fold:

  • straight pins or safety pins, or hem clips if the fabric marks easily
  • a full-length mirror on a hard floor, since carpet pile hides how close the fabric really sits to the ground
  • a tape measure
  • a second person, because bending over to check your own hem pulls the fabric up

Look at the hem allowance inside the leg before you start. That folded-under fabric is all the length you can ever get back, and some ready-made pants have very little, so a pair that's already too short with your boots may not be fixable.

Pin the hem in six steps

Do the steps in order, because fabric that shrinks later or a stance that shifts will undo a careful pin.

  1. Wash first if the fabric can shrink. Cotton, linen and denim that you plan to machine-wash and dry can lose some length, so wash and dry them once, the way you always will, before measuring. Dry-clean-only pants can skip this step.
  2. Put on the boots and pants and stand on a hard floor. Wear the waistband where it normally sits. Pants hiked up during pinning end up short once they settle back down.
  3. Stand straight with your weight on both feet and your eyes forward. Looking down at the hem lifts the fabric slightly and throws off the length.
  4. Fold and pin the back first. For a full length, a rough guide is to have the back of the hem sit about half an inch above the floor, so the front falls over the top of the foot without bunching. For a cropped length, fold until the hem meets or slightly overlaps the top of the boot shaft. Pin all the way around and check from the side that the fold looks level.
  5. Walk, sit and climb a few stairs. Watch whether the heel catches the hem as you step and whether a cropped hem rides up to expose skin or sock when you sit. Adjust the pins until both look right.
  6. Measure and mark. Measure from the crotch seam to the pinned fold on both legs, since the two often differ slightly, and write the numbers down for your tailor or for your own hemming.

Ask the tailor to keep any spare allowance folded inside instead of cutting it off. If you change boots later, that fabric lets you lengthen the pants again.

Heeled and flat ankle boots need different hems

Heel height changes the right hem length, so the back of the hem needs to move up or down by roughly the difference between two heel heights. A hem set for high-heeled ankle boots will drag when you switch to flat ankle boots, and a hem set for flats will look short and expose the shaft once you add a heel.

Settle on one heel height for each pair of pants. If you wear both styles, keep your full-length pairs for heels or platforms and choose cropped styles for flats, where a visible boot looks intentional. Block heels and wedges are also easier on long hems than slim heels, which are more likely to catch the fold of a hem that's even slightly too long.

Mistakes that spoil the line

Pinning in the wrong shoes is the error a tailor can't see. If you show up in sneakers and say you'll wear the pants with boots, the tailor has to guess, so wear or bring the boots to the fitting.

Watch the boot shaft as well as the length. A wide or stiff shaft can push the fabric out into a ridge at the ankle, which shows most in thin, drapey fabrics. When you pair boots with wide-leg pants made of soft material, a slimmer shaft that sits close to the leg lets the fabric fall straight.

Avoid a cropped hem that stops partway between the ankle and the top of the boot. That in-between length leaves a band of sock or skin that breaks the line of the leg; either bring the hem down to meet the shaft or go to full length.

Finally, don't judge the hem only in the mirror while standing still. A length that looks perfect at rest can sweep the sidewalk or get stepped on once you walk.

Start with the boots you reach for most, put them on with your favorite wide-leg pair, and pin the back of one leg before deciding anything else.

Stores for United States · Change
Fashion partners Ad

Shop the boutiques

All partner stores
All partner stores

More in Boots

All Boots stories
Up next · keep scrolling Sheer or Opaque Tights: Which Should You Choose for an Elegant Look? The next story loads below as you scroll — no need to go back. Sheer or Opaque Tights: Which Should You Choose for an Elegant Look?