Ankle boots with wide leg trousers: how to get the hem length right

Ankle boots with wide leg trousers: how to get the hem length right

Ankle boots with wide leg trousers: how to get the hem length right

A pair of wide leg trousers can look smart with ankle boots or sloppy, and a few millimetres of fabric often decides which. Hem them too long and the back of the leg drags under the heel until it frays. Hem them too short and the leg ends at an awkward point where a slice of boot shaft, or sock, shows at the wrong height.

The fix is to choose one of two lengths before anyone picks up scissors: a full length that covers most of the boot and nearly grazes the floor, or a cropped length that shows the boot while meeting the top of its shaft. Then pin it while you're wearing the exact boots you plan to pair with the trousers.

Gather the boots and tools before you pin

Bring the boots you'll actually wear. Heel height and sole thickness set the hem, so pinning in trainers or bare feet gives a length that's wrong as soon as you change shoes. If you own several pairs of women's ankle boots with different heels, pick the pair you'll wear most often with these trousers.

You'll also need a few simple things to get an accurate fold:

  • straight pins or safety pins, or hem clips if the fabric marks easily
  • a full-length mirror on a hard floor, since carpet pile hides how close the fabric really sits to the ground
  • a tape measure
  • a second person, because bending over to check your own hem pulls the fabric up

Look at the hem allowance inside the leg before you start. That folded-under fabric is all the length you can ever get back, and some ready-made trousers have very little, so a pair that's already too short with your boots may not be fixable.

Pin the hem in six steps

Do the steps in order, because fabric that shrinks later or a stance that shifts will undo a careful pin.

  1. Wash first if the fabric can shrink. Cotton, linen and denim that you plan to machine-wash and tumble-dry can lose some length, so wash and dry them once, the way you always will, before measuring. Dry-clean-only trousers can skip this step.
  2. Put on the boots and trousers and stand on a hard floor. Wear the waistband where it normally sits. Trousers hitched up during pinning end up short once they settle back down.
  3. Stand straight with your weight on both feet and your eyes forward. Looking down at the hem lifts the fabric slightly and throws off the length.
  4. Fold and pin the back first. For a full length, a rough guide is to have the back of the hem sit about 1 cm above the floor, so the front falls over the top of the foot without bunching. For a cropped length, fold until the hem meets or slightly overlaps the top of the boot shaft. Pin all the way round and check from the side that the fold looks level.
  5. Walk, sit and climb a few stairs. Watch whether the heel catches the hem as you step and whether a cropped hem rides up to expose skin or sock when you sit. Adjust the pins until both look right.
  6. Measure and mark. Measure from the crotch seam to the pinned fold on both legs, since the two often differ slightly, and write the numbers down for your tailor or for your own hemming.

Ask the tailor to keep any spare allowance folded inside instead of cutting it off. If you change boots later, that fabric lets you lengthen the trousers again.

Heeled and flat ankle boots need different hems

Heel height changes the right hem length, so the back of the hem needs to move up or down by roughly the difference between two heel heights. A hem set for high-heeled ankle boots will drag when you switch to flat ankle boots, and a hem set for flats will look short and expose the shaft once you add a heel.

Settle on one heel height for each pair of trousers. If you wear both styles, keep your full-length pairs for heels or platforms and choose cropped styles for flats, where a visible boot looks intentional. Block heels and wedges are also easier on long hems than slim heels, which are more likely to catch the fold of a hem that's even slightly too long.

Mistakes that spoil the line

Pinning in the wrong shoes is the error a tailor can't see. If you turn up in trainers and say you'll wear the trousers with boots, the tailor has to guess, so wear or bring the boots to the fitting.

Watch the boot shaft as well as the length. A wide or stiff shaft can push the fabric out into a ridge at the ankle, which shows most in thin, drapey fabrics. When you pair boots with wide leg trousers made of soft material, a slimmer shaft that sits close to the leg lets the fabric fall straight.

Avoid a cropped hem that stops partway between the ankle and the top of the boot. That in-between length leaves a band of sock or skin that breaks the line of the leg; either bring the hem down to meet the shaft or go to full length.

Finally, don't judge the hem only in the mirror while standing still. A length that looks perfect at rest can sweep the pavement or get trodden on once you walk.

Start with the boots you reach for most, put them on with your favourite pair of wide leg trousers, and pin the back of one leg before deciding anything else.

Article in the category